8 Replies Latest reply on Jun 27, 2016 5:56 AM by Carlos_A

    program i210-AT with external flash

    Joseph_Wang Green Belt

       

      Hello,

       

       

       

      I try to program the i210-AT with external flash but the pci device id still keep at 0x1531,

       

      The device id should be 0x1533 after I program flash. Is it?

       

      And how can I also to program the MAC by eepromARMtool?

       

       

      And the follow my console log

       

       

        (1) Show basic information

      $ sudo ./eepromARMtool  

      Intel(R) Eeprom ARM Tool ARM OTP Programming Tool

       

      Provided under the terms of a CNDA. Do Not Distribute.

       

      Copyright(C) 2013 by Intel(R) Corporation

       

      NIC  BUS  DEV FUN Silicon      Memory Type Present

       

      ===  ===  ===  ===  ===== ======================

       

      1. 1      0    0    I210 INVM+FLASH

       

       

       

      (2)Burn Dev_Start_I210_Copper_NOMNG_16Mb_A2_3.25_0.03.hex file to flash (Winbond W25Q16DVSSIG).

       

      $ sudo ./eepromARMtool -write -NIC=1 -f=Dev_Start_I210_Copper_NOMNG_16Mb_A2_3.25_0.03.hex

       

      Intel(R) Eeprom ARM Tool NVM/OTP Programming Tool

       

      Provided under the terms of a CNDA. Do Not Distribute.

       

      Copyright(C) 2013-2014 by Intel(R) Corporation

       

      Version 0.6.7

       

      Flash wordsize reg val:  5 register 482a00

       

       

       

      (3) Reboot then check the lspci list

       

      ubuntu@tegra-ubuntu: lspci –vvv

       

      01:00.0 Ethernet controller: Intel Corporation Device 1531 (rev 03)

       

      Subsystem: Intel Corporation Device 0000

       

      Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-

       

      Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

       

      Latency: 0, Cache Line Size: 64 bytes

       

      Interrupt: pin A routed to IRQ 130

       

      Region 0: Memory at 32800000 (32-bit, non-prefetchable) [size=8M]

       

      Region 2: I/O ports at 1000 [size=32]

       

      Region 3: Memory at 32400000 (32-bit, non-prefetchable) [size=16K]

       

      Capabilities: [40] Power Management version 3

       

      Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

       

      Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-

       

      Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+

       

      Address: 0000000000000000  Data: 0000

       

      Masking: 00000000  Pending: 00000000

       

      Capabilities: [70] MSI-X: Enable- Count=5 Masked-

       

      Vector table: BAR=3 offset=00000000

       

      PBA: BAR=3 offset=00002000

       

      Capabilities: [a0] Express (v2) Endpoint, MSI 00

       

      DevCap:   MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us

       

      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+

       

      DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

       

      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-

       

      MaxPayload 128 bytes, MaxReadReq 512 bytes

       

      DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

       

      LnkCap:   Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us

       

      ClockPM- Surprise- LLActRep- BwNot-

       

      LnkCtl:     ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+

       

      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

       

      LnkSta:     Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

       

      DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Via WAKE#

       

      DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled

       

      LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-

       

      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       

      Compliance De-emphasis: -6dB

       

      LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-

       

      EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-

       

      Capabilities: [100 v2] Advanced Error Reporting

       

      UESta:      DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

       

      UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

       

      UESvrt:    DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

       

      CESta:      RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

       

      CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

       

      AERCap:  First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

       

      Capabilities: [140 v1] Device Serial Number 00-a0-c9-ff-ff-00-00-00

       

      Capabilities: [1a0 v1] Transaction Processing Hints

       

      Device specific mode supported

       

      Steering table in TPH capability structure

       

      Capabilities: [1c0 v1] Latency Tolerance Reporting

       

      Max snoop latency: 0ns

       

                Max no snoop latency: 0ns

       

       

       

      Joseph